E1 G.SHDSL Modem E1 over 2-Wire modem:GSDSL

E1 G.SHDSL Modem E1 over 2-Wire modem:GSDSL

E1 G.SHDSL Modem

E1 transfer through copper lines with 24AWG(0.5mm) and 26 AWG(0.4mm)

  • Description
  • Inquiry

E1 G.SHDSL Modem E1 over 2-Wire modem



GSDSL G.SHDSL Modem is FPGA-based 2-wire 2304Kbps modem. According with ITU G.SHDSL standard, with best concocting technology and very good frequency spectrum compatibility, It has 3.5km-9.7km transmission distance in special lines with 24AWG(0.5mm) and 26 AWG(0.4mm). It can be used in every high quality and high-speed telecom operation such as transmitting voice, data and images. It also supports N * 64Kbps rate (N=1~32) of interface of V.35 and E1(G.703). GSDSL has strong supervisory control function. You can learn the start-up, running and line malfunctioning and other functions from the panel. In case there is something wrong with the system, one can locate the fault conveniently with loop back test to administrate networks.

Not only with low operating cost, but it is also easy to operate, install and link. One can use the dial switch on the back panel to setup work mode and transmission rate while slave modem can automatically follow master modem rate (that is the rate switch of the slave dosen’t work). So you can administrate the remote equipments in networks.  There are many indicator LEDs on the panel to display work status and line of equipment

GSDSL are used in couple. One is set up into Master Mode which is always placed at Telecommunication office. The other is set up into Slave Mode which is always put in the terminal of user



Line interface

Fully conforming to standard of YDN 056-1997

Transmission rate: N*64Kbps+8Kbps(N=3~36)
Code: PAM16
Line impedance: 135ohm
Signal electrical level: +13.5±0.5dbm
Line wire interface: a pair of passive twisted-line, RJ45
Code error rate: ≤10-9
Transmission distance without linkup: 3.5~9.7Km(0.4~0.8mm wire size)

Data interface 1 (E1 interface)

Transmission  rate: N * 64Kbps(N=1~32)
Line code: HDB3
Line impedance: 75ohm/120ohm
Interface standard: conform with CCITT G.703 standard

Data interface 2 (V.35 /V.24)

Transmission rate: N *64Kbps(N=3~36);

V24(64K; 128K;)

Work mode: DCE

Work circumstances

Power supply: 220VAC±10%,50Hz;48VDC(optional)
Power consumption: <5W
Volume: 225mm*145mm*40mm



Relative humidity:

0 oC~ +40 oC




40G module
QSFP+ transceiver

100G transceiver
QSFP28 SR4 transceiver
QSFP28 LR4 transceiver
CFP transceiver
CFP2 transceiver
CFP4 transceiver

PDH Multiplexer
SDH Multiplexer
E1 Converter
TDM over IP
PCM Multiplexer
Fiber Media Converter
Fiber Video Converter
SFP fiber module

Physiotherapy equipment
Walking Rehabilitation
Upper limb rehabilitation
Lower limb rehabilitation
Whole body rehabilitation
Children rehabilitation
Finger rehabilitation
CPM series
Treatment table series
Lumbar and neck traction bed
Medical mask

Low Temperature Freezer
-45℃ freezer
-60℃ freezer
-80℃ freezer
deep freezer
ultra low temperature freezer
cold room