100 Gb/s CFP LR4 Transceiver
100 Gb/s CFP LR4 Transceiver
- Description
- Inquiry
100G CFP LR4 Transceiver
PRODUCT FEATURES
Compliant with 100GBASE-LR4
Support line rates from 103.125 Gbps to 111.81 Gbps
Integrated LAN WDM TOSA / ROSA for up to 10 km reach over SMF
CAUI(10x10G) Electrical Interface and 4-lane 25.78Gb/s optical interface
Duplex LC optical receptacle
MDIO Interface for module management
Single 3.3 V power supply
Case operating temperature range:0°C to 70°C
Power dissipation < 12W
APPLICATIONS
Local Area Network (LAN)
Data Center
Ethernet switches and router applications
STANDARD
Compliant to IEEE 802.3ba
Compliant to CFP MSA Hardware Specification
Compliant to CFP MSA Management Interface Specification
General Description
The FASTFOM CFP LR4 Transceiver is the optical transceiver module which is a hot pluggable form factor designed for high speed optical networking application. The FASTFOM CFP LR4 is designed for 100 Gigabit Ethernet application and provides 100GBASE-LR4 compliant optical interface, CAUI electrical interface and MDIO module management interface.
The FASTFOM CFP LR4 Transceiver converts 10-lane 10.3Gb/s electrical data streams to 4-lane LAN-WDM 25.78Gb/s optical output signal and 4-lane LANWDM 25.78Gb/s optical input signal to 10-lane 10.3Gb/s electrical data streams. This 10-lane 10.3Gb/s electrical signal is fully compliant with IEEE 802.3ba CAUI specification. The high performance Cooled LAN-WDM EA-DFB transmitter and high sensitivity PIN receiver provide superior performance for 100Gigabit Ethernet applications up to 10km links and compliant optical interface with IEEE802.3ba 100GBASE-LR4 requirements.
The FASTFOM CFP LR4 contains a duplex LC connector for the optical interface and a 148-pin connector for the electrical interface. Figure 1 shows the functional block diagram of FASTFOM CFP LR4.
Transmitter
The transceiver module receives 10-lane 10.3 Gb/s CAUI electrical inputs. The gearbox multiplexes 10- lane electrical signals to 4-lane electrical signals. The multiplexed 4-lane signals are fed to the transmitters. The four transmitters convert 4-lane signals to an optical signal through 4 Laser drivers and Lasers diodes which are packaged in the Transmitter Optical Sub-Assembly (TOSA). Each Laser launches optical signal in specific wavelength specified in IEEE802.3ba 100GBASE-LR4 requirements. These 4-lane optical signals will be optically multiplexed into one fiber by 4 to1 Optical WDM MUX which is in the TOSA. The optical output power is held constant by an automatic power control (APC) circuit. The transmitters output can be turned off by TX_DIS hardware signal and/or through MDIO module management Interface.
Receiver
The FastFOM CFP LR4 receives 4-lane LAN WDM optical signals. The optical signals are demultiplexed by 1 to 4 optical DE-MUX and fed into each Receiver Optical Sub-Assembly(ROSA)integrated 1:4 optical DE-MUX. The ROSA converts optical signal to electrical signal. The 4-lane
regenerated electrical signals are de-multiplex to 10-lane signals by the 4 to 10 gearbox. The 10-lane signals are compliant with IEEE CAUI interface requirements. Each received optical signal is monitored by the DOM section. The monitored value is reported through the MDIO section. If one or more received optical signal is weaker than the threshold level, RX_LOS hardware alarm will be launched
40G module
QSFP+ LR4
QSFP+ transceiver
100G transceiver
QSFP28 SR4 transceiver
QSFP28 LR4 transceiver
CFP transceiver
CFP2 transceiver
CFP4 transceiver
PDH Multiplexer
SDH Multiplexer
E1 Converter
TDM over IP
Modem
PCM Multiplexer
Fiber Media Converter
Fiber Video Converter
SFP fiber module
Ultra Low Temperature Freezer
Speed Reducer
Rehabilitation Equipment
Fiber Optical Multiplexer